0:00
Now we have a bit of a shower issue. Both of our showers drain to the bilge and they have the shower sums
0:08
But the pipes are broke off. So I'll show you the aft bathroom first and show you what we have to do
0:18
So down under this floor by the aft head There's our battery
0:27
41% down there, but the shower nozzles just broke off right there
0:37
We'll start by removing this drain. Okay, here goes nothing. Let me see if I can record this
0:46
Yep. It's tie enough. That one's in there sideways
1:05
Look at that. Rolling sideways. So I don't think that one screw is the original one
1:18
I think this is going to be a bigger job than what I think it's going to be. Let's see
1:33
Let's see if that pops up. And there's our hole. Battery cables and everything
1:43
This does not look original. There another screw that holding this piece down So I going to take this off took this piece off the bottom here So I gonna see if I can reattach this some way a little bit better
1:58
Okay, so we have two screws, one each side. Remove these. I'm going to show
2:06
Let's see Let's see if this thing pops out
2:23
Okay, it does pop out, but I have to be careful because I don't want to break this
2:29
And so I'm a chisel away at this silicone, some more. Why cleaning in here
2:35
in here. So I think I have this thing cleaned up as best I can. And this, they tried
2:45
to J.B. Weld at once, but they tried it from here. There's no J.B. Weld on this. So we've taken
2:52
apart. And we're going to load some J.B. Weld in here and squish it together and see how
2:57
that works. Six minutes set time. It's nice and windy out here. Hopefully you can hear me
3:04
We're going to set this up. And this is just a one-to-one ratio
3:10
I have a little stirring device. So this is the steel, this is the hardener
3:16
So I can pour this out here. This will never set. I think that's enough
3:28
The hardener. This is when the time starts ticking
3:38
So paste a little bit of that That about the same amount Don get the steel in with the hardener
3:49
It will never open again. So we'll mix this up. And I'm looking for a nice, kind of a dark gray consistency
4:06
Almost black. I don't know what color is that. You tell me
4:38
I'm trying to do is get a good solid thick codeine all the way around this thing
4:52
So it squishes out. I like it when it squishes. Make sure it's nice and even here
5:03
I think that should do it. So these are the ones to screw in, so I've got to do it this way
5:36
See guys I think it got it sealed all the way around
5:43
It's already got a lip in there, so it should already be sealed, but I want to fill in all the holes around it
5:50
Like that. Looks good. And now I got to hold this until my hand gets too tired
5:55
So we got this glued. You see it. It's pretty good. And now I've got beetle tape around it
6:03
My wife's ideal, because I was going to jump and just get the caulk and fill it up like the last people
6:09
But this should be easier to clean. And then on the screw holes, I put beetle tape over there where the screws are going to go through
6:20
And I'm not going to use the other screw holes that they drilled in there because then they screwed this down
6:26
And then they mounted the screen on top. I'm just going to mile it all together as one piece
6:32
So as you can see down there, there's our pipe. And I'm going to put this direction in the direction of our pipe
6:40
And hopefully I can line up these screws, which I did. And screw them in
6:47
So let me get this. I'm going to, I'm going to hand screwing. So let me go offline here
6:52
And we'll get the bottom screw down. So we have the drain in
6:56
and I've already tested this, but I'll show you what we did. You look up in there
7:02
I actually did put some more J.B. Weldye just to make sure it holds in
7:06
so it took another couple hours. So now let's run some water in the shower
7:10
See if the sump works. So drain our tanks. There it goes
7:22
Hear it? Yeah. Sumping. Thank you
